Panasonic TV service mode
PANASONIC-1
1 For chassis AMEDP, APEDP, AREDP ...
Press ACTION (TV turned on)
Select SET-UP icon, set antenna to CABLE
Select TIMER icon, set sleep timer to 30
Press ACTION twice to exit menus and tune to channel 124
Adjust volume to 0
Press VOL - on TV control panel and red 'CHK' will appear in the upper left corner
To toggle between Serviceman and Aging Modes press ACTION and VOL + simultaneously on the control panel
The set is now in Serviceman Mode, press POWER on remote to select one of the five Serviceman Adjustment Modes:
B = VCJ Sub Adjustments
C = VCJ Cut-off Adjustments
S = Options (PIP and Clock Adjsutments)
M = MTS Adjsutments
'CHK' = Normal operation of CHANNEL and VOLUME controls
Press CHAN UP / DOWN on remote to select an item
Press VOL LEFT / RIGHT to adjust
PANASONIC-2
Short test point FA1 to cold ground FA2 (A-board: TP pin 8 to pin 3)
Receiver is in Aging Mode with yellow 'CHK' in the upper-left corner
Press ACTION and VOL+ simultaneously on the control panel and 'CHK' should be in red
The set is now in Serviceman Mode, press POWER on remote to select one of the five Serviceman Adjustment Modes:
B = VCJ Sub Adjustments
C = CRT Adjustments
D = Pincushion Adjustments
S = Options Adjustments (PIP and clock)
Press CHAN UP / DOWN on remote to select an item
Press VOL LEFT / RIGHT to adjust
PANASONIC-3
TX-W28R3 (and similar models)
Set BASS to maximum position, set TREBLE to minimum position
Press REVEAL on the remote control and at the same time press VOLUME on the TV.
This will place the TV into the Service mode
Press the RED / GREEN buttons to select an item
Press the YELLOW / BLUE buttons to adjust
Press STORE on the preset panel after each adjustment has been made to store the required values
To exit the Service Mode, press NORMALIZATION
RCA/GE CTC175 thru CTC187
Turn TV on - Press and hold MENU - Press POWER - Press VOL+
P00 and V00 will be displayed (left and right sides of screen)
Release MENU - Press VOL+ to set V00 to no. V76
Press CH+ to select an adjustment that you want to change ( ???P00??? )
Press VOL+ and VOL- to adjust ( ???V00??? )
P01 Horiz Freq P07 Red Bias
P02 Horiz Phase P08 Grn Bias
P03 EWDC P09 Blu Bias
P04 EW amp P10 Red Drive
P05 Vert Cent P11 Grn Drive
P06 Vert Size P12 Blue Drive
PANASONIC- 4
Panasonic TV's after 1996 can be set to "Serviceman Mode" with the
following remote control sequence:
-select the SET-UP icon and select CABLE mode.
-select the TIMER icon and set the SLEEP timer for 30 minutes.
-press the ACTION button twice to get out of the menus.
-change to channel 124.
-adjust the volume to minimum (0).
-Hit the VOL down button on the TV itself (not on
the remote) and a red "CHK" should appear in the upper corner.
-press the ACTION and VOLUME DOWN buttons (again, on the
TV, not the remote) you will toggle between AGING and SERVICEMAN modes.
Select Serviceman mode. The POWER button on the remote control will
select one of the five Serviceman Adjustment modes.
The modes are:
B - Serviceman VCJ SUB Adjustments. These include sub-tint,
sub-color, sub-brightness, sub-contrast, colorkiller/ABL/gamma,
audio and video adjustment, and vertical size.
C - Serviceman VCJ Cut-off adjustments. These include Red, Green
and Blue cut-off, red and blue drive, automatic fine tuning
(AFT), RF AGC (RF gain control), horizontal center, beam limit,
etc.
S - Serviceman Options Adjustments. These involce the PIP and
clock.
M - Serviceman MTS (Stereo/SAP) adjustments.
CHK - the mode you first entered. Normal picture and sound, lets
you check things over and still have a hotkey into the
service menu.
There is one more adjustment that isn't in the five modes, it's
global. When in either the yellow or red CHK mode, you can press
RECALL on the remote control to enter the purity field check mode.
This lets you select a pure white, red, green, or blue screen. A
good thing to walk away from if you just want to temporarily freak
out the floor manager, but it will be fixed as soon as the TV is
turned off. Oh well.
To get out of Serviceman mode, press ACTION and POWER on the
receiver simultaneously for at least 2 seconds. The TV will momentarily
shut off and then comes back on.
----------------------------------------------------------------------------------
PE77U / PX75U / PX77U / PZ700U / PZ750U
PD60U / PX6U / PX60U / PX600U
PD50U / PX50U / PX500U :
* Hold down the {VOL -} button ON THE PLASMA TV.
* Press the {RECALL} button 3 times on the remote.
* The Service Menu will be displayed.
* Use {1} {2} on remote to navigate main menu items.
* Use {3} {4} on remote to navigate sub-menu items.
* Use {VOL+} {VOL -} on remote to change item value.
* Write down all values before changing
Once a value is changed, THE CHANGE IS MADE.
* Power off to exit service mode and save.
PANASONIC-5
PA25UP / PD25UP / PX25UP :
* Using the remote control:
* Press the {MENU} button.
* Set "Antenna A" to "Cable".
* Select "Timer" menu and set sleep timer to 30 min.
* Press {OK} twice to exit menus.
* Tune to channel 124.
* Press and hold {VOL -} button ON THE PLASMA TV.
"CHK" appears in on top-left corner followed by 5 letter/numbers
(which are the cumulative hours in hex numbers)
* While the "CHK" is displayed, press the {OK} and {VOL+} buttons
ON THE TV simultaneously to toggle between Modes:
 Red "CHK" for Serviceman  Yellow "CHK" for Aging â€â€Â
* Press the {POWER} button on the remote to select one of the six
Serviceman Adjustments Modes.
A. MTS ADJUSTMENT
B. CLOCK ADJUSTMENT
C. VIDEO ADJUSTMENT
D. HDEF ADJUSTMENT
E. VDEF ADJUSTMENT
F. DAF ADJUSTMENT
G. OTHER ADJUSTMENT
* Press {CH+} {CH -} on the remote to select the settings
on each of Service Adjustment Modes.
Write down the original values before modifying anything.
It's easy to erroneously adjust the wrong item.
* Press {VOL+} {VOL -} on the remote to change values.
* Press the {POWER} button on the TV to exit the service menu.
PANASONIC-6
PA20UP / PX20UP :
* Using the remote control:
* Press the {MENU} button.
* Press "Setup" menu.
* On "Mode" menu, select "Cable"
* Select "Timer" menu and set sleep timer to 30 min.
* Press {ACTION} twice to exit menus.
* Tune to channel 124.
* Press and hold {VOL -} button ON THE PLASMA TV.
"CHK" appears in on top-left corner followed by 5 letter/numbers
(which are the cumulative hours in hex numbers)
* While the "CHK" is displayed, press the {ACTION} and {VOL+} buttons
ON THE TV simultaneously to toggle between Modes:
 Red "CHK" for Serviceman  Yellow "CHK" for Aging â€â€Â
* Press the {POWER} button on the remote to select one of the six
Serviceman Adjustments Modes.
A. MTS ADJUSTMENT
B. CLOCK ADJUSTMENT
C. VIDEO ADJUSTMENT
D. HDEF ADJUSTMENT
E. VDEF ADJUSTMENT
F. DAF ADJUSTMENT
G. OTHER ADJUSTMENT
* Press {CH+} {CH -} on the remote to select the settings
on each of Service Adjustment Modes.
Write down the original values before modifying anything.
It's easy to erroneously adjust the wrong item.
* Press {VOL+} {VOL -} on the remote to change values.
* Press the {POWER} button on the TV to exit the service menu.
PANASONIC- 7
LCDs / CRTs / RPTVs :
* Hold down the {VOL -} button ON THE TV.
* Press the {RECALL} button 3 times on the remote.
* The Service Menu will be displayed.
* Use {1} {2} on remote to navigate main menu items.
* Use {3} {4} on remote to navigate sub-menu items.
* Use {VOL+} {VOL -} on remote to change item value.
* Write down all values before changing
Once a value is changed, THE CHANGE IS MADE.
* Power off to exit service mode and save.
Model PT45LC12:
1. Press and hold Vol Dn on center panel and press recall button on remote until Work Mode is displayed on screen.
2. Press and hold Vol Dn on TV and Swap button button on remote until Factory Adjust is displayed on the screen
3. Use Channel Dn button to select Digital and press the Action button.
PANASONIC- 8
PROJECTORS :
* Press the {MENU} button.
* Go to "Options" menu.
* Highlight "OSD".
* Then press and hold the {ENTER} button,
until the Service Menu is displayed.
* Press the {MENU} button to exit.
PANASONIC- 9
PROJECTORS:
# Turn the Projector on.
# Press the {POWER} button.
# A "Power Off" confirmation will come up on screen.
# Then press {LEFT} {UP} {DOWN} {UP} {DOWN}
& {ENTER} buttons.
# The Service Menu will be displayed.
# To exit, turn the Projector Off.
PANASONIC- 10
PLASMAS 8UK / 9UK:
* Hold down the {VOL -} button ON THE PLASMA DISPLAY.
* Press the {STATUS} button 3 times on the remote.
(Status button is the one above Setup button)
* The Service Menu (CAT) will be displayed.
(CAT = Computer Aided Test Menu)
* Use the cursors keys on the remote to select a mode.
* And press the Action key {} to access the menu.
* To exit each mode, press the {R} button.
* To exit the CAT menu, press the {STATUS} button.
* Press {POWER} button on the Plasma to exit the service mode.
PANASONIC- 11
PLASMAS 3UY / 4UY / 5UY / 6UY / 7UY:
* Hold down the {VOL -} button ON THE PLASMA DISPLAY.
* Press the {STATUS} button 3 times on the remote.
(Status button is the one below Power button)
* The Service Menu (CAT) will be displayed.
(CAT = Computer Aided Test Menu)
* Use the cursors keys on the remote to select a mode.
* And press the Action key {} to access the menu.
* To exit each mode, press the {R} button.
* To exit the CAT menu, press the {STATUS} button.
* Press {POWER} button on the Plasma to exit the service mode.
Panasonic TV service mode
Panasonic TX-33AK10.mode service
Bass to max.
Treble to min.
Hold down "index"
Press "-" (minus) on the front of the set
Panasonic EURO-2 mode service
CTV Service Mode
In Sound-Menu Low-tone-regel to maximum and
High-tone-regel to minimum. Press 'F' button on TV.
Then press VOL- on TV and REVEAL on remote control in
some time. Select press red and green buttons.
Adjust press yellow and blue buttons. Store press
'STR'. Exit press 'N' on remote control.
Panasonic TV service mode 2
Panasonic TX-25W3E mode service
Increase the bass to maximum, decrease treble to minimum, press RESET on the remote control and while in the TV-volume. Using the Teletext press RED and GREEN selects the
item with Blue and Yellow line values. To store the new press STORE. To exit NORM (normalization).
Panasonic Plasma 3UY mode service
Press the volume down & hold down the button on the plasma TV display.
Press 3 times the STATUS button on the remote control.
Status button is the one below Power button
The Service Menu mode CAT will comes up.
CAT is Computer Aided Test Menu
To select a mode parameter use the cursors keys on the remote control.
And press the Action key {} to access the menu.
To exit mode Press the R button.
RELATED SERVICE CODE / MODE
AIWA AKAI AKIRA BUSH FUJITEC CHINA GOLD STAR HITACHI HONDAI ICHIKO JVC KCL LG MAGNAVOX MITSUBISHI PANASONIC PHILIPS SONY SONY-2 SAMSUNG SANSUI SANYO TCL TCL-2 TOSHIBA VIDEOCON
FOR INDIAN LIVE TV CHANNELS YOU CAN DOWNLOAD THESE APP
THIS APP ARE ABSOLUTELY FREE
NO EXTRA CHARGES
---TAGS--
TV AERIAL COLOUR CODES
SERVICE ELECTIC TV CODES
TV SERVICE MENU CODES
PANASONIC TV SERVICE CODES
MITSUBISHI TV SERVICE CODES
SAMSUNG TV MAINTENANCE CODE
REMOTE SERVICE CODE FOR COLOUR TV FREE
BPL COLOUR TV SERVICE MANUAL
SERVICE ELECTRIC TV REMOTE CODES
AKAI TV SERVICE MENU CODE
SANSUI TV SERVICE MENU CODE
SAMSUNG TV SERVICE MENU CODE
SONY TV SERVICE MENU CODE
LG TV SERVICE MENU CODE
Tidak ada komentar: