OLED PANASONIC Curved TV - TX-65CZ952B - SERVICE MODE � BLINKING CODES � PANEL ADJUSTMENT � SELF CHECK
PANASONIC OLED TV TX-65CZ952B � SERVICE MODE � POWER LED BLINKING CODES � PANEL ADJUSTMENT � SELF CHECK - HOME MODE SHOP MODE - OLED PANEL TEST MODE
OLED PANEL TEST MODE
To find the possible failure point where in OLED Panel, FR board or A board when the abnormal picture is displayed.
Step 1
Step 1
Go into OLED Panel test mode and confirm the symptom
While pressing [VOLUME ( - )] button of the main unit, press [YELLOW] button of the remote control three times within 2 seconds. [Service Mode]
The several test patterns generated by OLED Panel are displayed.
Judge by the following method
Still abnormal picture is displayed: The cause must be in OLED Panel. Exit test mode.
Normal picture is displayed: The cause must be in A board or FR board. Go into FR test mode
Step 2.
While pressing [VOLUME ( - )] button of the main unit, press [YELLOW] button of the remote control three times within 2 seconds. [Service Mode]
The several test patterns generated by OLED Panel are displayed.
Judge by the following method
Still abnormal picture is displayed: The cause must be in OLED Panel. Exit test mode.
Normal picture is displayed: The cause must be in A board or FR board. Go into FR test mode
Step 2.
Go into FR test mode and confirm the symptom
During in OLED Panel test mode, press [OK] button on the remote control.
The test pattern generated by FR board is displayed.
Judge by the following method
Abnormal picture is displayed: The cause must be in FR board.
Normal picture is displayed: The cause must be in A board.
Step 3
During in OLED Panel test mode, press [OK] button on the remote control.
The test pattern generated by FR board is displayed.
Judge by the following method
Abnormal picture is displayed: The cause must be in FR board.
Normal picture is displayed: The cause must be in A board.
Step 3
Go into Additional OLED Panel test mode
During in FR test mode, press [OK] button on the remote control.
The several additional test patterns generated by OLED Panel are displayed.
Result and Judgment are same as step 1.
Step 4.
During in FR test mode, press [OK] button on the remote control.
The several additional test patterns generated by OLED Panel are displayed.
Result and Judgment are same as step 1.
Step 4.
How to Exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control in OLED Panel test mode or FR test mode.
Remarks
1. During OLED Panel test mode and FR test mode, Power LED red and green are flashing alternately.
2. To display the test pattern in FR mode, input signal from HDMI, AV or antenna terminal. If no signal input, the test pattern won�t be generated and no test pattern is displayed.
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control in OLED Panel test mode or FR test mode.
Remarks
1. During OLED Panel test mode and FR test mode, Power LED red and green are flashing alternately.
2. To display the test pattern in FR mode, input signal from HDMI, AV or antenna terminal. If no signal input, the test pattern won�t be generated and no test pattern is displayed.
POWER LED BLINKING TIMING CHART
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
LED Flashes Orange - Panel adjustment in progress (This is not malfunction). It takes approximately 10 minutes (20 minutes max.).
PANEL ADJUSTMENT FUNCTION
The use of the OLED panel for a long period causes no uniformity of charge in each OLED cell and there is a possible cause of "image retention�.
To reduce the "image retention" Panel adjustment function is newly introduced for OLED models TX-65CZ950 series.
When "image retention" is not reduced by this function it seems that the "image retention" is permanent due to deterioration of OLED cell.
During the Panel adjustment period please avoid touching or exerting any pressure on the screen e.g. wiping the screen, etc. If the Panel adjustment has been completed LED lights Red or Orange (standby mode).
The Panel adjustment function starts running automatically after switching off to standby if the TV has been in operation for at least 3 hours since the last panel adjustment.
If the Panel adjustment has been interrupted before completion it will start again after the next switching off to the standby mode.
To reduce the "image retention" Panel adjustment function is newly introduced for OLED models TX-65CZ950 series.
When "image retention" is not reduced by this function it seems that the "image retention" is permanent due to deterioration of OLED cell.
During the Panel adjustment period please avoid touching or exerting any pressure on the screen e.g. wiping the screen, etc. If the Panel adjustment has been completed LED lights Red or Orange (standby mode).
The Panel adjustment function starts running automatically after switching off to standby if the TV has been in operation for at least 3 hours since the last panel adjustment.
If the Panel adjustment has been interrupted before completion it will start again after the next switching off to the standby mode.
How to activate Panel adjustment function manually
Step 1
Step 1
Change from �Home� mode to �Shop� mode
1. �MENU� button on remote control is pushed
and while selecting "Picture" in menu press �Green� button
on remote control for more than 3 seconds.
2. OSD screen is displayed. "Shop" is selected.
Step 2
1. �MENU� button on remote control is pushed
and while selecting "Picture" in menu press �Green� button
on remote control for more than 3 seconds.
2. OSD screen is displayed. "Shop" is selected.
Step 2
Pull out and insert the main plug. After TV turns on
Panel adjustment function is activated.
Step 3
Panel adjustment function is activated.
Step 3
Change from �Shop� mode to �Home� mode after finish this function.
1. OSD screen is displayed according to the procedure of Step1.
2. Select �Home� mode
Note: When TV has already been set to �Shop� mode the procedure of Step1 and Step3 is unnecessary.
1. OSD screen is displayed according to the procedure of Step1.
2. Select �Home� mode
Note: When TV has already been set to �Shop� mode the procedure of Step1 and Step3 is unnecessary.
Self Check
Self-check indication only
While pressing [VOLUME ( - )] button on the main unit, press [BLUE] button on the remote control.
Self-check indication and forced to factory shipment setting
While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
How to exit
Switch off the power with the [POWER] button on the main unit.
Self-check indication only
While pressing [VOLUME ( - )] button on the main unit, press [BLUE] button on the remote control.
Self-check indication and forced to factory shipment setting
While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
How to exit
Switch off the power with the [POWER] button on the main unit.
[If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K."]
CLICK ON THE PICTURES TO MAGNIFY
Tidak ada komentar: